Notes for Nand2Tetris: Memory

This is a note for Nand2Tetris unit 3.

So many pictures in this unit. Highly recommended to read the textbook.

Unit 3.1

Combinatorial Logic vs Sequential Logic

Combinatorial:
Sequential:

Unit 3.2

Flip Flops (触发器)

Sequential Logic

The Clock Data Flip Flop (DFF):

DFF

Implementation of the DFF:

In this course, it’s a primitive
In many physical implementations, it may be built from actual Nand gates:
1. create a “loop” achieving an “un-clocked” flip flop
1. isolation across time steps using a “master-slave” step up

Bit (1-bit Register):

Bit

if load[t-1]:
    out[t] = in[t-1]
else:
    out[t] = out[t-1]

w (word width): 16-bit, 32-bit, 64-bit …
Register’s state: the value which is currently stored in the register

RAM unit:

A sequence of addressable registers, which addresses to .

At any given point of time, only one register in the RAM is selected.

k (width of address input):

RAM

Unit 3.3

Memory:

Main memory: RAM …
Secondary memory: disks …
volatile / non-volatile

Unit 3.4

Counter’s three possible control settings:

Reset:
Next:
Goto:

if reset[t] == 1:
    out[t+1] = 0
elif load[t] == 1:
    out[t+1] = in[t]
elif inc[t] ==1:
    out[t+1] = out[t] + 1
else:
    out[t+1] = out[t]

Project 3

Bit.hdl

Just follow the implementation given in the course, and build a Bit with a Mux and a DFF:

/**
 * 1-bit register:
 * If load[t] == 1 then out[t+1] = in[t]
 *                 else out does not change (out[t+1] = out[t])
 */

CHIP Bit {
    IN in, load;
    OUT out;

    PARTS:
    Mux(a=dffout, b=in, sel=load, out=dffin);
    DFF(in=dffin, out=out, out=dffout);
}

Register.hdl

A Register is 16 Bits.

/**
 * 16-bit register:
 * If load[t] == 1 then out[t+1] = in[t]
 * else out does not change
 */

CHIP Register {
    IN in[16], load;
    OUT out[16];

    PARTS:
    Bit(in=in[0], load=load, out=out[0]);
    Bit(in=in[1], load=load, out=out[1]);
    Bit(in=in[2], load=load, out=out[2]);
    Bit(in=in[3], load=load, out=out[3]);
    Bit(in=in[4], load=load, out=out[4]);
    Bit(in=in[5], load=load, out=out[5]);
    Bit(in=in[6], load=load, out=out[6]);
    Bit(in=in[7], load=load, out=out[7]);
    Bit(in=in[8], load=load, out=out[8]);
    Bit(in=in[9], load=load, out=out[9]);
    Bit(in=in[10], load=load, out=out[10]);
    Bit(in=in[11], load=load, out=out[11]);
    Bit(in=in[12], load=load, out=out[12]);
    Bit(in=in[13], load=load, out=out[13]);
    Bit(in=in[14], load=load, out=out[14]);
    Bit(in=in[15], load=load, out=out[15]);
}

RAM8.hdl

Use DMux to choose which address to load, then use Mux to get the loaded values.

/**
 * Memory of 8 registers, each 16 bit-wide. Out holds the value
 * stored at the memory location specified by address. If load==1, then
 * the in value is loaded into the memory location specified by address
 * (the loaded value will be emitted to out from the next time step onward).
 */

CHIP RAM8 {
    IN in[16], load, address[3];
    OUT out[16];

    PARTS:
    DMux8Way(in=load, sel=address,
             a=reg0l, b=reg1l, c=reg2l, d=reg3l,
             e=reg4l, f=reg5l, g=reg6l, h=reg7l);
    Register(in=in, load=reg0l, out=reg0o);
    Register(in=in, load=reg1l, out=reg1o);
    Register(in=in, load=reg2l, out=reg2o);
    Register(in=in, load=reg3l, out=reg3o);
    Register(in=in, load=reg4l, out=reg4o);
    Register(in=in, load=reg5l, out=reg5o);
    Register(in=in, load=reg6l, out=reg6o);
    Register(in=in, load=reg7l, out=reg7o);
    Mux8Way16(a=reg0o, b=reg1o, c=reg2o, d=reg3o,
              e=reg4o, f=reg5o, g=reg6o, h=reg7o,
              sel=address, out=out);
}

RAM64.hdl

Group the addresses.

Based on RAM8.

/**
 * Memory of 64 registers, each 16 bit-wide. Out holds the value
 * stored at the memory location specified by address. If load==1, then
 * the in value is loaded into the memory location specified by address
 * (the loaded value will be emitted to out from the next time step onward).
 */

CHIP RAM64 {
    IN in[16], load, address[6];
    OUT out[16];

    PARTS:
    DMux8Way(in=load, sel=address[3..5],
             a=ram80l, b=ram81l, c=ram82l, d=ram83l,
             e=ram84l, f=ram85l, g=ram86l, h=ram87l);
    RAM8(in=in, load=ram80l, address=address[0..2], out=ram80o);
    RAM8(in=in, load=ram81l, address=address[0..2], out=ram81o);
    RAM8(in=in, load=ram82l, address=address[0..2], out=ram82o);
    RAM8(in=in, load=ram83l, address=address[0..2], out=ram83o);
    RAM8(in=in, load=ram84l, address=address[0..2], out=ram84o);
    RAM8(in=in, load=ram85l, address=address[0..2], out=ram85o);
    RAM8(in=in, load=ram86l, address=address[0..2], out=ram86o);
    RAM8(in=in, load=ram87l, address=address[0..2], out=ram87o);
    Mux8Way16(a=ram80o, b=ram81o, c=ram82o, d=ram83o,
              e=ram84o, f=ram85o, g=ram86o, h=ram87o,
              sel=address[3..5], out=out);
}

RAM512.hdl

Based on RAM64.

/**
 * Memory of 512 registers, each 16 bit-wide. Out holds the value
 * stored at the memory location specified by address. If load==1, then
 * the in value is loaded into the memory location specified by address
 * (the loaded value will be emitted to out from the next time step onward).
 */

CHIP RAM512 {
    IN in[16], load, address[9];
    OUT out[16];

    PARTS:
    DMux8Way(in=load, sel=address[6..8],
             a=ram640l, b=ram641l, c=ram642l, d=ram643l,
             e=ram644l, f=ram645l, g=ram646l, h=ram647l);
    RAM64(in=in, load=ram640l, address=address[0..5], out=ram640o);
    RAM64(in=in, load=ram641l, address=address[0..5], out=ram641o);
    RAM64(in=in, load=ram642l, address=address[0..5], out=ram642o);
    RAM64(in=in, load=ram643l, address=address[0..5], out=ram643o);
    RAM64(in=in, load=ram644l, address=address[0..5], out=ram644o);
    RAM64(in=in, load=ram645l, address=address[0..5], out=ram645o);
    RAM64(in=in, load=ram646l, address=address[0..5], out=ram646o);
    RAM64(in=in, load=ram647l, address=address[0..5], out=ram647o);
    Mux8Way16(a=ram640o, b=ram641o, c=ram642o, d=ram643o,
              e=ram644o, f=ram645o, g=ram646o, h=ram647o,
              sel=address[6..8], out=out);
}

RAM4K.hdl

Based on RAM512.

/**
 * Memory of 4K registers, each 16 bit-wide. Out holds the value
 * stored at the memory location specified by address. If load==1, then
 * the in value is loaded into the memory location specified by address
 * (the loaded value will be emitted to out from the next time step onward).
 */

CHIP RAM4K {
    IN in[16], load, address[12];
    OUT out[16];

    PARTS:
    DMux8Way(in=load, sel=address[9..11],
             a=ram5120l, b=ram5121l, c=ram5122l, d=ram5123l,
             e=ram5124l, f=ram5125l, g=ram5126l, h=ram5127l);
    RAM512(in=in, load=ram5120l, address=address[0..8], out=ram5120o);
    RAM512(in=in, load=ram5121l, address=address[0..8], out=ram5121o);
    RAM512(in=in, load=ram5122l, address=address[0..8], out=ram5122o);
    RAM512(in=in, load=ram5123l, address=address[0..8], out=ram5123o);
    RAM512(in=in, load=ram5124l, address=address[0..8], out=ram5124o);
    RAM512(in=in, load=ram5125l, address=address[0..8], out=ram5125o);
    RAM512(in=in, load=ram5126l, address=address[0..8], out=ram5126o);
    RAM512(in=in, load=ram5127l, address=address[0..8], out=ram5127o);
    Mux8Way16(a=ram5120o, b=ram5121o, c=ram5122o, d=ram5123o,
              e=ram5124o, f=ram5125o, g=ram5126o, h=ram5127o,
              sel=address[9..11], out=out);
}

RAM16K.hdl

Based on RAM4K.

/**
 * Memory of 16K registers, each 16 bit-wide. Out holds the value
 * stored at the memory location specified by address. If load==1, then
 * the in value is loaded into the memory location specified by address
 * (the loaded value will be emitted to out from the next time step onward).
 */

CHIP RAM16K {
    IN in[16], load, address[14];
    OUT out[16];

    PARTS:
    DMux4Way(in=load, sel=address[12..13],
             a=ram4K0l, b=ram4K1l, c=ram4K2l, d=ram4K3l);
    RAM4K(in=in, load=ram4K0l, address=address[0..11], out=ram4K0o);
    RAM4K(in=in, load=ram4K1l, address=address[0..11], out=ram4K1o);
    RAM4K(in=in, load=ram4K2l, address=address[0..11], out=ram4K2o);
    RAM4K(in=in, load=ram4K3l, address=address[0..11], out=ram4K3o);
    Mux4Way16(a=ram4K0o, b=ram4K1o, c=ram4K2o, d=ram4K3o,
              sel=address[12..13], out=out);
}

PC.hdl

PC is Program Counter.

/**
 * A 16-bit counter with load and reset control bits.
 * if      (reset[t] == 1) out[t+1] = 0
 * else if (load[t] == 1)  out[t+1] = in[t]
 * else if (inc[t] == 1)   out[t+1] = out[t] + 1  (integer addition)
 * else                    out[t+1] = out[t]
 */

CHIP PC {
    IN in[16], load, inc, reset;
    OUT out[16];

    PARTS:
    Inc16(in=original, out=increased);
    Mux16(a=original, b=increased, sel=inc, out=o1);
    Mux16(a=o1, b=in, sel=load, out=o2);
    Mux16(a=o2, b=false, sel=reset, out=o3);
    Register(in=o3, load=true, out=out, out=original);
}

My current understanding here is not yet complete. But as I understand it now, the thinking here should be as follows:

First, the idea about this one Inc16 and three Mux16s. Let’s split this four-branch conditional

if      (reset[t] == 1) out[t+1] = 0
else if (load[t] == 1)  out[t+1] = in[t]
else if (inc[t] == 1)   out[t+1] = out[t] + 1  // (integer addition)
else                    out[t+1] = out[t]

into nested three-level if-else statements. Since Mux can only choose which state to keep, and cannot choose what state is needed before calculating that state, we have to analyze this nested if-else statement from the innermost level outwards. And, in terms of requirements, the top requirement will override the bottom requirement, i.e. the reset instruction will hide the load instruction, and the load instruction will hide the inc instruction. By working from the bottom up, we achieve exactly this override.

From the innermost level outwards

In order to use Mux, it is logical to find out what the new state of the current state (original) should be after reset, load and inc. The new state after reset is false, and the new state after load is in, without any computation. Only the state after inc needs to be obtained using Inc16, in this case which is increased.

Next, the original. At first I thought this was in, but in fact, because of the sequential logic, all operations here should be done on the basis of the current state of the chip in the PC. So, here the current state is noted as original and this original is updated on the last line.